Happymodel Mobula7 1S 75mm Whoop FPV Racing Drone, ELRS BNF/PNP, RS0802 20000KV Motor, Caddx Ant Camera

Description

24g Happymodel Mobula7 1S 75mm Whoop FPV Racing Drone ELRS BNF/PNP w/ RS0802 20000KV Motor Runcam Nano3 Camera

Introducing the Happymodel Mobula7 1S 75mm Whoop FPV Racing Drone, a top choice for drone enthusiasts. This micro FPV whoop drone features a cutting-edge 5-IN-1 AIO flight controller with ExpressLRS 2.0, offering exceptional RX and VTX range. Equipped with the new RS0802 brushless motors and a Caddx Ant camera, it ensures smooth and powerful flight performance. The drone is compatible with 1S Lipo/LIHV batteries, recommended sizes being 450mAh, 550mAh, or 650mAh. The onboard OpenVTX supports up to 400mw, providing RCE and PIT modes, making it ideal for racing events. With a lightweight design and advanced features, the Mobula7 1S is perfect for both beginners and seasoned racers.

The O4 Version Clink Here
Notice:
1. Due to Runcam Nano3 camera was discontinued, now the Mobula7 1s comes with Caddx ant camera .
2. The Frsky version of the flight controller supports D8/D16, but not D16 V2.
Happymodel Mobula7 1S Micro FPV Whoop Drone
We＊re glad to launched our new Mobula7 drone , this time the 75mm whoop based on 1s power. Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1s Will be the best choice in the whoop season.
The world first 5-IN-1 AIO flight controller with ExpressLRS 2.0 , OPENVTX(up to 400mw), 12A Brushless Blheli_S ESC and Betaflight OSD coming out recently. This is amazing flight controller for Brushless whoop. You could get unbelievable RX and VTX range by using this flight controller.
The new RS0802 motors comes with a new unibell design, use 1.5mm shaft and include PCB bottom plate, high efficiency and much more reliable.
New onboard OpenVTX , max power up to 400mw, provide RCE and PIT mode, it was very useful for race event.
Features:
– X12 5-IN-1 AIO flight controller built-in 2.4G ELRS V2.0 and Openvtx
– VTX Power up to 400mw
– ELRS V2.0 Support
– NEW RS0802 20000KV motors
– Runcam Nano3 The lightest 1/3 CMOS 800TVL Camera
– Smooth and powerful
– Compatible for 1S Lipo/LIHV
– Recommend 1S 450mah/550mah/650mah battery (Not included)
Specifications:
Brand Name: Happymodel
Item Name: Mobula7 1S 75mm Micro FPV whoop drone
Wheelbase: 75mm
Size: 99mm*99mm*40mm
Weight: 24g

Motor

Mode: RS0802 KV20000
Configu-ration:9N12P
Stator Diamter:8mm
Stator Length:2mm
Shaft Diameter:朴1.5mm
Motor Dimension(Dia.*Len):朴10.5mm*13.5mm
Weight(g):2.0g
No.of Cells(Lipo):1S only

Propellers

Weight:0.24g
Material:PC
Pitch:1 inch
Props Dia:40mm
Center Thickness:5mm
Center Hole Dia:1.5mm

Flight controller

X12 ELRS V1.0 flight controller built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280
X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver Target: CRAZYBEEF4FR
X12 Flysky V1.0 flight controller built-in SPI Flysky 2.4G receiver Target: CRAZYBEEF4FS
X12 PNP V1.0 flight controller without onboard receiver Target: CRAZYBEEF4DX
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU6000 or ICM20689(SPI connection)
Mount hole size: 25.5mm*25.5mm
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 12A(each) Blheli_S 4in1 ESC
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G OpenVTX 0mw~400mw
Built-in ExpressLRS 2.4G,Frsky D8/D16,Flysky AFHDS 2A
Built-in voltage detection
Built-in current sensor

Onboard 4in1 ESC

Power supply: 1S LiPo/LiPo HV
Current: 12A continuous peak 15A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: Z_H_30_REV16_7.HEX
Default protocol: DSHOT300
Support Bluejay firmware

Onboard SPI ExpressLRS 2.4GHz Receiver
( 2.4G ELRS Receiver Version)

Packet Rate option: 50Hz/150Hz/250Hz/500Hz
ExpressLRS Firmware version: V2.0
RF Frequency: 2.4GHz
Antenna: SMD antenna
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS
Compatible with ExpressLRS V2.0 TX Module
Couldn＊t flash separately ExpressLRS firmware

Onboard Frsky SPI D8/D16 receiver compatible
( Compatible Frsky Receiver Version)

SPI BUS receiver Frsky D8 compatible
Compatible Non-EU transmitter D8 model
Channels: 8ch
No ground interference ( Transmitter and receiver 1 m from the ground): 200meter
Failsafe support

Onboard Flysky SPI receiver compatible
( Compatible Flysky Receiver Version)

SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground): 200meter
Failsafe support

PNP Version (without onboard receiver)

Full UART1 for external Receiver
Support CRSF/GHOST/SBUS/IBUS/DSMX protocol
IR1 pad(invert RX1) used for SBUS input

Onboard 5.8g OPENVTX

Firmware version: OPENVTX
Smart audio v2.1
PIT Mode support
RCE Mode support
Channels:48ch
Transmitting Power: 0/RCE/25mw/100mw/400mw
Power supply: DC 5V
Current (5v): <650ma (400mw)

Runcam Nano3

Model: RunCam Nano 3
Image Sensor: 1/3′ CMOS
Horizontal Resolution: 800TVL
Lens : 2.1mm(M8) FOV 150～
Signal System: NTSC
S/N Ratio: >50dB
Electronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: 0.01Lux@1.2F
D-WDR: Auto
Day/Night: Color
Power:DC 3-5.5V
Current: 110mA@5V 120mA@3.3V
Housing Material: ABS
Net Weight: 1.2g
Dimensions: L14mm*W14mm*H9mm

Recommend 1S Lipo Battery(Not included)

Capacity: 650mAh
Voltage: 3.8v
Continuous Discharge Rate: 30C
Instantaneous discharge rate: 60C
Size: 60mmx18mmx8mm
Weight: 16g
Connector: PH2.0
Product Link

Package Included:
1 x Mobula7 1S 75mm whoop Drone Frame (Mobula7 v4 frame) 1 x Option1: X12 ELRS V1.0 flight controller built-in SPI ELRS 2.4G receiver 1 x Option2: X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver 1 x Option3: X12 Flysky V1.0 flight controller built-in SPI Flysky 2.4G receiver 1 x Option4: X12 PNP V1.0 flight controller without onboard receiver 4 x RS0802 KV20000 brushless motor 1 x Gemfan 1610-2 bi-blade propellers (4cw+4ccw) 1 x Runcam Nano3 1/3 CMOS 800TVL camera 1 x Onboard 5.8G Openvtx 0mw~400mw VTX 1 x 1S parallel charging board 1 x Propeller disassemble tool 1 x Extra camera canopy