Matek Systems ELRS-R24-P6 R24-P6 ExpressLRS 2.4GHz PWM Receiver With Antenna Support 2~8S VBat Voltage Sense For FPV RC Racing Drone
Matek Systems ELRS-R24-P6 R24-P6 ExpressLRS 2.4GHz PWM Receiver With Antenna Support 2~8S VBat Voltage Sense For FPV RC Racing Drone
Description:
Brand: Matek Systems
Model: ELRS-R24-P6
Item: PWM Receiver
ESP8285, SX1281
Antenna connector: IPEX MHF 1
6x PWM outputs
Support 2~8S VBat voltage sense
RF Frequency: 2.4GHz (2400~2480MHz)
Telemetry power: 12dbm
Receiver output protocol: PWM
Input voltage: 4~9V DC @ pad
Voltage sense: 34V Max. @ ??VBatpad
Power dissipation: 45mA(binding), 85mA(wifi mode)
PCB size: 20mm x 18mm
Weight: 2g w/ antenna
Firmwares
* ExpressLRS 3.0 or newer, DIY 2.4GHz / DIY 2400 RX PWMP EX.
* ExpressLRS wiki for PWM receiver, Click HERE
* Make sure Receiver and TX module both are running ExpressLRS 3.0 or newer.
??????????????????????????????????
* Receiver has ExpressLRS 3.0 preloaded with binding phrase ‘123456’, the Receiver will never enter binding mode if using the traditional binding procedure.
* You need to reflash it with your binding phrase OR go into WebUI to set your binding phrase.
Flashing via Wifi
* Disconnect ESC and servos from receiver first.
* Power on receiver by 5V source. Receiver’s LED(Red) will blink slow at first, and after 20s, it should blink fast indicating it’s on Wifi Hotspot Mode.
* More detailed steps, pls refer this page.
* Target: DIY 2.4 GHz / DIY 2400 RX PWMP EX.
Flashing via UART
* Disconnect ESC and servos from receiver first.
* Wire the receiver into the USB-TTL adapter, with TX on receiver connected to the Rx on the USB-TTL, and RX on receiver connected to the Tx of the USB-TTL. Wire 5V and GND of the USB-TTL to 5V and GND of the Receiver.
* Press the boot button while powering on the receiver, then release the Red LED on receiver should now be solid.
* Select the target DIY 2.4 GHz / DIY 2400 RX PWMP EX and ??UARTfor Flashing Method, set your bind phrase and Firmware Options and once done, click on Build and Flash.
Package Included:
1x Matek Systems ELRS-R24-P6 Receiver
1x IPEX MHF1 Antennas. 15cm
Dupont 2.54 pins (Board is shipped unsoldered)
Sterling -
The quality of this product is unmatched. Impressive!
9NI5KSn2Rc -
I have 7 of these products, and they meet my needs.
RMFfodmp -
I received the product and was pleasantly surprised to find an extra little gift included.
Odette -
Five stars for this amazing product!
Emerson -
These products are appropriately priced, especially with 1.
Kyle -
The product was fantastic, and the bonus coupon was a thoughtful addition.
Kenyon -
I've never been so satisfied with a purchase. Five stars!
GSR -
The product's functions were a bit unclear to me, but the customer service team explained everything comprehensively.
4eR1Cr4lpm -
Matek Systems ELRS-R24-P6 R24-P6 ExpressLRS 2.4GHz PWM Receiver With Antenna Support 2~8S VBat Voltage Sense For FPV RC Racing Drone is my new favorite thing. It's incredible!
Kay -
I'm amazed at how well this Radios & Receiver product performs.
70CBsMjT -
I had to exercise some patience, but the product is worth it.
puz8BRDekU -
Despite the extended delivery time, the product is functional.
0G9f -
I had some initial struggles with the product, but the customer support team's expertise was invaluable.
Thora -
The product arrived in a flash, and it's a game-changer.
U70aNbuDh -
The logistics delay was a slight inconvenience, but the product is fine.
Stephen -
I can't say enough good things about the product, and the extra gift was the cherry on top.
Shana -
This product is a lifesaver. I can't thank you enough!
6Mj -
I can't get enough of this product. It's incredible!
3WlchVU -
I'm constantly impressed with the results from using this.
Marc -
I'm amazed at how well this Radios & Receiver product performs.
AX1 -
I'm extremely satisfied with Matek Systems ELRS-R24-P6 R24-P6 ExpressLRS 2.4GHz PWM Receiver With Antenna Support 2~8S VBat Voltage Sense For FPV RC Racing Drone. Five stars!