Happymodel Crux35 ELRS V2 3.5-Inch 4S Ultralight FPV Racing Drone BNF with Runcam Link Wasp Nano Camera

Description

Happymodel Crux35 ELRS V2 Analog / Crux35 Digital HD 150mm 3.5 Inch 4S Ultralight FPV Racing Drone BNF w/ Runcam Link Wasp Nano / ANT 1200tvl Camera

The Happymodel Crux35 ELRS V2 is a 3.5-inch ultralight FPV racing drone designed for agility and performance. Weighing just 87g for the analog version and 108g for the digital HD version, it offers an exhilarating freestyle flying experience. Equipped with the high-efficiency Happymodel EX1404 motors and HQPROP three-blade propellers, it ensures an optimal thrust-to-weight ratio. The analog version features a Caddx ANT camera, while the digital HD version is equipped with a Runcam Link Wasp Nano camera. The drone supports both UART ExpressLRS and SPI Frsky receivers, catering to different preferences. Compatible with 3-4S batteries, it delivers a flight time of 9 to 15 minutes with a recommended 4S 750mAh battery.

NOTICED:
SPI ELRS version Crux35/Crux35 HDZERO/Crux35 HD were discontinued. The new ELRS V2 version comes with CrazyF411 ELRS AIO flight controller built-in UART ExpressLRS receiver.
Feb. 11th, 2023
Nebula Nano has been stopped produced. Change it into Runcam Link Wasp Nano.
Introduction:
CRUX35/CRUX35 HD is an ultra-lightweight 3.5Inch FPV Freestyle FPV Racing Drone, the weight of the whole drone is only 87g for the analog version and 108g for the digital HD version. The Crux35 serials drone use Happymodel EX1404 high-efficiency motor and HQPROP 3.5-inch three-blade propeller to ensure the largest thrust-to-weight ratio under the most efficient premise, which can bring you a smooth Freestyle flying experience.
The HD version is equipped with CADDXFPV Nebula and Vista HD image transmission system. The analog version is equipped with CADDXFPV Ant ant camera.The receiver version can be SPI ExpressLRS and SPI Frsky (S-FHSS compatible) for choose.ExpressLRS is the most popular RC link system by now , it could performance very well with Crux35 and Crux35 HD.
Features:
Ultra-lightweight 3.5-inch BNF FPV Freestyle Drone
HD video transmission and analog video transmission are optional
Integrated ExpressLRS SPI receiver or Frsky SPI D8/D16 receiver
High efficiency EX1404 power system
Can be equipped with Naked Gopro or SMO4K
Support 3-4S battery 4S 750mah battery is recommended, maximum support 4S 1100mah
Specifications: ( Manual of ELRS Version / Frsky Version)
Brand: Happymodel
Model: Crux35 Analog / Crux35 HD
Wheelbase: 150mm
Weight: 87g ( Analog); 108g ( HD)
Size: 130mmx130mmx45mm(without propellers)
Version Optional: Analog / HD
Receiver optional: UART ExpressLRS 2.4GHz (ELRS 2.4G RX) / SPI Frsky D8/D16 (S-FHSS compatible)
Camera option: HD version Nebula+Vista
Analog version Ant+OVX303 VTX
Flying time: 9min~15min 4s 750mah battery

Motor

Mode: EX1404
KV options: KV3500
Configu-ration:9N12P
Stator Diamter:14mm
Stator Length:4mm
Shaft Diameter: ?1.5mm
Motor Dimension(Dia.*Len):?15mm*15mm
Weight:9g

Propellers

Propeller Diameter: 3.5 inch
Pitch : 2
Blades : 3
Material : Poly Carbonate
Weight : 1.5g
Hub Diameter : 10mm
Hub Thickness:4.7mm
Shaft :1.9/1.5/1.9mm
Adaptor Rings : NO

Flight controller
(ELRS Version)

MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: ICM42688P or BMI270 (SPI Control)
Mount pattern: 25.5沁25.5 M2
Size:32*32*5mm
Power supply: 2-4S Lipo battery
Built-in 20A Blheli_s ESC each
Built-in Betaflight OSD(SPI Control)
Built-in UART ExpressLRS 2.4GHz receiver
Built-in 5V 1.5A BEC
Flight controller firmware target: CRAZYBEEF4DX

Flight controller
(Frsky version)

Model: CrazybeeF411 FRSKY
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: BMI270 or ICM42688P(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 2-4S battery input (DC 8V-17V)
Built-in 20A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Frsky D8/D16 SPI receiverBuilt-in 2.4G Power Amplification
Built-in Betaflight OSD(SPI Control)
Built-in Current meter
Built-in 5V 1.5A BEC
Built-in voltage detectionFirmware target: MATEKF411RX

Onboard 4in1 ESC

MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HV
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT300

Onboard UART ExpressLRS 2.4GHz Receiver
(ELRS 2.4G Receiver version)

Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHzAntenna plug: IPEX
Telemetry output Power: <12dBm
Receiver protocol: CRSF
Default firmware version: ExpressLRS V3.0.1

Onboard SPI Frsky 2.4GHz receiver ( SPI Frsky Receiver Version)

SPI BUS receiver
Frsky D8/D16/EU-LBT/, Futaba S-FHSS switchable on Betaflight
Channels: 8ch/16ch
Dual antenna
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 400m

Runcam Link Wasp Nano
(Digital HD version)

Runcam Link Wasp Nano

Caddx ANT 1200tvl camera
(Analog version)

Image Sensor: 1/3′ CMOS Sensor
Horizontal Resolution: 1200 TVL
TV System: NTSC or PAL
IMAGE: 16:9 or 4:3
Synchronization: Internal
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
S/N Ratio : >52dB (AGC OFF)
Video Output: CVBS
Lens: 1.8mm
Min. Illumination: 0.001Lux@F1.2
Auto Gain Control: YES
BLC: YES
WDR: Global WDR
DNR: 3D DNR
Dimensions: 14*14mm(with bracket to 19*19mm)
Wide Power Input: DC 3.7-18V
Work Temperature: -20﹠~+60﹠
Weight: 2g (N.W.)

OVX303 5.8Ghz VTX
(Analog version)

Model: OVX303
Frequency: 5.8G 40CH
Transmitting Power: 0/RCE/25mw/100mw/300mw
Power supply: DC 5V
Current (5v): <650ma (300mw)
Weight: 1.5gram without antenna
Antenna: RHCP

Recommended(Not Included):
4S: 750mah Battery

Package Included:
1 x Crux35 Frame
1 x Analog FPV Camera Caddx Ant (Analog version)
1 x Happymodel OVX303 5.8G analog VTX (Analog version)
1 x CaddxFPV Digital HD Kit (HD version)
4 x Happymodel EX1404 KV3500 Brushless Motor
1 x HQProp T3.5X2X3Grey (4cw+4ccw)
1 x Screw Driver
1 x Buckle for Battery
Option1: CrazyF411 ELRS FC with UART ELRS
Option2: CrazyF411 FRSKY FC SPI Frsky