30.5×30.5mm Holybro Kakute H7 V2 Flight Controller Tekko32 F4 4in1 50A / 65A ESC Atlatl HV V2 800mW VTX Stack for RC Drone FPV Racing
Specification: ( Diagram Picture)
Brand: Holybro
Model: Kakute H7 V2 Stack
Optional Version: 50A / 65 A
| Kakute H7 V2 Flight Controller | MCU – STM32H743 32-bit processor running at 480 MHz IMU – BMI270 Barometer – BMP280 OSD – AT7456E Onboard Bluetooth chip – ESP32-C3 SpeedyBee IOS & Android App Compatible Note: The Bluetooth onboard is set to automatically turn off when the flight controller is unlocked (arm) and turn on automatically when the flight controller is locked (disarm). VTX ON/OFF Pit Switch nbsp;Switch can be enable using USER1 in Betaflight Mode tab. Warning: Do not enable this pit switch if you are using DJI FPV Remote Controller 6x UARTs (1,2,3,4,6,7; UART2 is used for Bluetooth telemetry) 9x PWM Outputs (8 Motor Output, 1 LED) 2x JST-SH1.0_8pin port (4in1 ESCs, x8/Octocopter compatible) 1x JST-GH1.25_6pin port (For HD System like Caddx Vist A& Air Unit) Battery input voltage: 7V to 42V BEC 5V 2 ACont. BEC 9V 1.5 ACont. Mounting – 30.5 x 30.5mm/??4mm hole with ??3mm Grommets Dimension – 35x35mm Weight – 8g |
| Tekko32 F4 4in1 50A ESC ( Optional) | F4 MCU @150Mhz / PWM output up to 96K / 4~6S / BLHeli32 / 30×30 The all new Tekko32 is the first 4in1 ESC in market to adapt the fast F4 MCU @150Mhz, providing Asmooth control operation and quick response. Features: New and faster F4 MCU @ 150Mhz (compared to F3 @108Mhz & F0 @48Mhz) PWM Frequency: 16k to 96k Separate drive & control circuit, this broadens the current capability of the drive circuit while reducing the electrical interference to the control circuit. Specification: Continuous Current: 50 Ax4 Burst Current: 60 Ax4 Supports 4-6S battery Supports DShot 150/300/600/1200 & MultiShot/OneShot/Proshot/PWM etc. ESC telemetry Supported Onboard analog current sensor No output BEC BLHeli_32 firmware 1000uf 35v capacitor included (highly recommended for 6s setup) Amperage meter scale ratio: 168 Dimensions: 45x37x6mm / Weight: 13.8g Mounting holes: M4 30.5×30.5mm (M3 grommets included) |
| Tekko32 Metal 4in1 65A ESC ( Optional) | F4 MCU @150Mhz / Metal-Cased MOSFET / PWM output: 16k ~96k PWM / 4~6S / BLHELI32 The all new Tekko32 Metal is the first 4in1 ESC in the market to adapt the fast F4 MCU. Powerful & reliable metal-cased MOSFET 4in1 ESC with smooth control and quick response. Rev v1.7 Updated: Amperage meter scale ratio: 180 Features: New & faster F4 MCU @ 150Mhz (compared to F3 @108Mhz & F0 @48Mhz) PWM Frequency: 16k to 96k Metal-cased MOSFET for excellent heat dissipation Massive on-board capacitance for noise filtering at 2068uf 3 oz copper PCB design to allow bigger current and better heat dissipation Separate drive & control circuit, this broadens the current capability of the drive circuit while reducing the electrical interference to the control circuit. Specification: Continuous Current: 65 Ax4 Burst Current: 75 Ax4 Supports 4-6S battery Supports DShot 150/300/600/1200 & MultiShot/OneShot/Proshot/PWM etc. ESC telemetry Supported Onboard analog current sensor No output BEC BLHeli_32 firmware 1000uf 35v capacitor included (highly recommended for 6s setup) Amperage meter scale ratio: 180 Dimensions: 43 x 44mm / Weight: 15.8g Mounting holes: M4 30.5×30.5mm (M3 grommets included) Note: Air flow for the ESC is very important if you want to run this 4in1 in high current. The battery wire (from Lipo to 4in1 ESC) should be at least 12AWG and well soldered. |
| Atlatl HV V2 VTX ( Manual) |
Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW Audio: 6.5 MHz Mono Protocol??smart audio2.0 Antenn AConnector: MMCX Input Voltage: 7 to 28 volts (2-6S LiPo) with absolute maximum 42 volts Dimensions: 35x25x7mm (Includes USB height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 9.3g |
Package Included:
1x Kakute H7 V2 Flight Controller
1x Atlatl HV V2 VTX
1x 50A OR 65A ESC ( Optional)
1x Electrolytic capacito: 1000uF 35v
1x 8pin to 8pin 1mm pitch 65mm cable
1x 8pin to 8pin 1mm pitch 25mm cable
1x JST GHR 8pin to JST GHR 6pin 80mm cable (for DJI/Caddx HD System)
1x JST GHR 6pin 100mm cable(for Caddx HD Systems)
1x 80mm SMA?CMMCX Cable
1x JST GHR 4pin 150mm cable
Additional information
| Weight | 0.0825 kg |
|---|---|
| Version: No selection | 50A, 65A |
Reviews
There are no reviews yet.