SpeedyBee F7 V3 BL32 50A Stack Flight Controller with 5V/9V BEC, 4in1 Brushless ESC for FPV Racing Drone

Description

30.5×30.5mm SpeedyBee F7 V3 BL32 50A Stack OSD Flight Controller w/ 5V 9V BEC 50A 4in1 Brushless ESC 3-6S for Master 5 V2 FPV Racing Drone

The SpeedyBee F7 V3 Flight Controller is engineered for optimal performance in FPV racing drones. It features an STM32F722 MCU, BMI270 gyro, and BMP280 barometer, providing precise flight control. The built-in 2.4 GHz Wi-Fi and Bluetooth combo chip allows for wireless firmware updates and configuration. Compatible with DJI systems, it supports both 6-pin connector and direct soldering. The flight controller offers multiple power outputs, including 5V, 9V, 3.3V, and 4.5V, accommodating various components. The SpeedyBee BL32 50A 4-in-1 ESC supports DSHOT300/600 protocols and includes a heat sink and TVS protective diode for enhanced durability. This stack is ideal for drones powered by 3S to 6S LiPo batteries.

Specification: ( Manual)

Product Name

SpeedyBee F7 V3 Flight Controller

MCU

STM32F722

IMU(Gyro)

BMI270

USB Port Type

Type-C

Barometer

BMP280

OSD Chip

AT7456E chip

BLE Bluetooth

Supported. Used for Flight Controller configuration,built-in a single 2.4 GHz Wi-Fi-and-Bluetooth combo chip

Flash FC Firmware Wirelessly

Supported. Please enter MENU > FC Firmware Flasher

Download/Analyze Blackbox

Supported.Please enter MENU > Blackbox Analyzer

DJI Air Unit Connection Way

Two ways supported: 6-pin connector or direct soldering.

6-pin DJI Air Unit Plug

Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.

Flash(for BlackBox)

500MB

BetaFlight Camera Control Pad

Yes(CC pad on the front side)

Power Input

3S – 6S Lipo

5V Output

10 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A.

9V Output

2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A.

3.3V Output

Supported. Designed for 3.3V-input receivers. Up to 500mA current load.

4.5V Output

Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.

ESC Signal Pads

M1 – M4 on bottom side and M5-M8 on front side.

UART

5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6)

ESC Telemetry UART

R4(UART4)

I2C

Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.

LED Pad

Used for WS2812 LED controlled by Betaflight firmware.

Buzzer

BZ+ and BZ- pad used for 5V Buzzer

BOOT Button

Supported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.

RSSI Input

Supported. Named as RS on the front side.

SmartPort

Supported

Supported Flight Controller Firmware

BetaFlight(Default),INAV

Firmware Target Name

SPEEDYBEEF7V3

Mounting

30.5 x 30.5mm( 4mm hole diameter)

Dimension

41(L) x 38(W) x 8.1(H)mm

Weight

10.7g

Product Name

SpeedyBee BL32 50A 4-in-1 ESC

Firmware

SpeedyBee BL32 50A

Configurator Download Link

http://github.com/bitdump/BLHeli/releases

Continuous Current

50A * 4

Burst Current

55A(5seconds)

TVS Protective diode

Yes

Heat Sink

Yes

External Capacitor

1000uF Low ESR Capacitor(In the package)

ESC Protocol

DSHOT300/600

PWM Frequency Range

16KHz-128KHz

Power Input

3-6S LiPo

Power Output

VBAT

Current Sensor

Support (Scale=490 Offset=0)

ESC Telemetry

supported

Mounting

30.5 x 30.5mm( 4mm hole diameter)

Dimension

45.6(L) * 40(W) * 8.8mm(H)

Weight

19.2g with heat sink

Package Included:
1 x SpeedyBee F7 V3 Flight Controller
1 x SpeedyBee BL32 50A 4-in-1 ESC
1 x DJI 6pin Cable (80mm)
1 x SH 1.0mm 25mm-length 8pin Cable
1 x M3 8mm Silicone Grommets
1 x M3 8.1mm Silicone Grommets
5 x M3 30mm Inner-hexagon Screws
5 x M3 Silicone O Ring
5 x M3 Nylon Nut
1 x 35V 1000uF Low ESR Capacitor
1 x XT60 Power Cable (70mm)
1 x 4pin SH1.0 to 3+2pin JST1.25 FPV Cam Cable (30mm)
1 x 4pin SH1.0 to 3+2pin JST1.25 FPV Cam Cable (60mm)
1 x 4pin SH1.0 to 4pin JST1.25 FPV Cam Cable (60mm)
1 x 4pin SH1.0 Radio Receiver Cable (100mm)
1 x 4pin SH1.0 to 4pin SH1.0 Analog VTX Cable
1 x 6pin SH1.0 GPS Module Cable without Connector (100mm)
1 x 6pin SH1.0 GPS Module Cable Connector